Get a quoteRequest a demonstration

Pre-clean inspection report

DPF pre-clean inspection reports

The METClean S and XL Multi+ can email a PDF inspection report before the wash. It records the machine’s back-pressure reading and the findings entered by the technician.

See it for yourself

A real report from a demo job, and the film of that job from start to finish.

Use the report alongside the vehicle’s diagnostics and your inspection to explain why you recommend a clean, a repair or further investigation.

Example pre-clean inspection report

Page 1 of the example pre-clean report MC-20261105-1148-7: the pre-test back-pressure reading in the CLOGGED band, cleaning required; the cleaning journey; oil contamination and a blown flexi found. The full text follows under Read this report as text.
A real report from a demo job at MET, as the machine emails it.
Read this report as text

DPF test precondition report

Report no. MC-20261105-1148-705/11/2026 11:48

Pre-test back pressure

153 mbar

CLOGGEDCleaning required

  • OK0 to 15 mbar
  • DIRTY16 to 30 mbar
  • CLOGGEDOver 30 mbar

DPF condition

  • AdBlue contamination: not found
  • Oil contamination foundExtra care has been taken to carry out a full wash even though the DPF has oil contamination.
  • Blown flexi foundPlease ensure you carry out exhaust repairs before fitting this back to the vehicle.

Test details

Test no.
7
Customer
Operator
KAREN
Date
05/11/2026
Time
11:48

Build the diagnosis before you wash

A blocked filter is a symptom. Before you wash it, put three things together: what the vehicle’s diagnostics say, what you can see on the filter and exhaust, and how hard the filter resists air. The machine gives you the last one, and the report keeps all three findings with the job.

  1. Check the vehicle

    Read the fault codes and live data, and note anything that could have blocked the filter, such as a sensor, injector or EGR fault.

  2. Inspect the filter

    Look at the faces of the filter and the exhaust it came from. Tick what you find on the machine’s screen: AdBlue contamination, oil contamination or a blown flexi.

  3. Run the pre-test

    Fit the filter exactly as for cleaning and press Pre Test. The machine passes air through the filter and records the back-pressure reading.

  4. Fill in the ticket

    Add the company, operator and customer details. Regular customers are stored, so repeat work is quick.

Explain why you recommend a clean

The reading shows how restricted the filter is. Your inspection and the vehicle’s diagnostics show why. Together they let you say, in plain words, what you found and what you recommend: a clean, a repair first, or both.

  • High reading, sound exhaust, no faults on the vehicle: a clear case for cleaning, with the reading to show for it.
  • Low reading: check the filter for cracks or melting before you clean. A damaged filter lets air bypass, so it can read low and still be faulty.
  • AdBlue contamination recorded: clean the filter and have the AdBlue system checked, so the deposits don’t build up again.
  • Oil contamination recorded: clean the filter and find where the oil came from, so the customer isn’t back with the same problem.
  • Blown flexi recorded: quote the exhaust repair separately, so the cleaned filter goes back on a sound exhaust.

Each tick is something the technician saw, recorded so the customer can see it too. The recommendation is still yours to make.

Send the findings before the customer decides

On the METClean S and XL Multi+ the report is emailed as a PDF as soon as the pre-test finishes, to the customer or fleet contact and to your own inbox. They see the reading, what you found and who inspected the filter, on their phone, before you start the wash.

  • A copy lands in your office inbox for the job file, and you can still print one.
  • Fleet managers can forward it to whoever signs off the work.
  • When the customer says yes, the filter is already on the machine and ready to clean.
METClean XL Multi+
Yes, from the machine, before cleaning; printing still available
METClean S
Yes, from the machine, before cleaning; printing still available
METClean E
No
METClean V
No
METClean DPF Lite
No

Read the sample report

This is a report from one MET demonstration. The pressure bands and recommendation shown belong to this example. Use the test setup, the filter inspection and the vehicle’s diagnostics when interpreting a reading.

Example report

Example pre-clean inspection report

A real report from a demo job at MET, as the machine emails it before the clean: the pre-test back-pressure reading and its band, the condition findings the technician recorded, the test details and the verification code.

Download the example report (PDF)PDF, 75 KB, 2 pages

Example pre-clean inspection report

Page 1 of the example pre-clean report MC-20261105-1148-7: the pre-test back-pressure reading in the CLOGGED band, cleaning required; the cleaning journey; oil contamination and a blown flexi found. The full text follows under Read this report as text.
Page 2 of the example pre-clean report: operator, date and time, the certified authentic block with its verification code, and why there is no pressure test after cleaning.
A real report from a demo job at MET, as the machine emails it.
Read this report as text

DPF test precondition report

Report no. MC-20261105-1148-705/11/2026 11:48

Pre-test back pressure

153 mbar

CLOGGEDCleaning required

  • OK0 to 15 mbar
  • DIRTY16 to 30 mbar
  • CLOGGEDOver 30 mbar

Your DPF's cleaning journey

  1. Pre-testBack pressure measured before cleaning (this report)
  2. WashHeated water with cavitation bursts at the correct time intervals
  3. Dry100°C drying process
  4. CheckFinal check, ready to fit back to the vehicle

After this pre-test your DPF enters the METclean wash cycle: heated water with cavitation bursts at the correct time intervals, followed by a 100°C drying process and a final check. The whole process takes around 45 minutes.

DPF condition

  • AdBlue contamination: not found
  • Oil contamination foundExtra care has been taken to carry out a full wash even though the DPF has oil contamination.
  • Blown flexi foundPlease ensure you carry out exhaust repairs before fitting this back to the vehicle.

Test details

Test no.
7
Customer
Operator
KAREN
Date
05/11/2026
Time
11:48

Certified authentic

This report was produced by a genuine METclean DPF cleaning machine.

Authorised METclean owner: MET

Test no.: 7 · Verification code: D771-CC43-AE27

To verify this report, contact MET quoting the report number and verification code.

Why there is no pressure test after cleaning. This report records the DPF back pressure before cleaning. We never carry out a pressure test after cleaning, because the result would not be correct. The METclean drying process only ever partially dries the DPF, leaving it ready to fit back to the vehicle. Moisture still held in the monolith restricts the flow through it, so any reading taken at this stage would show a higher pressure than the true condition of the DPF. This applies to every cabinet DPF cleaning machine, not just METclean. No cabinet washing machine on the market can give an accurate post-clean pressure test, although some claim to. At METclean we believe in being open and transparent with our customers, so we do not produce a post-clean result that cannot be relied on. Driving the vehicle for 5 to 10 minutes after refitting completes the drying process. After refitting, please carry out a DPF reset on the vehicle, and find and fix any faults that caused the DPF to block, so it does not block again.

  1. The reading before cleaning

    Air is passed through the filter before the wash, and the reading is placed in its band: OK, DIRTY or CLOGGED. It shows how restricted the filter is; your inspection and the vehicle’s diagnostics show why.

  2. What the technician recorded

    The technician ticks what they saw. Oil contamination is a reason to find where the oil came from; a blown flexi is an exhaust repair to quote and fix before the filter goes back on.

  3. The job it belongs to

    Test number, customer, operator, date and time, with a verification code so the customer can check with MET that the report came from a genuine METClean machine.

Watch how it works

One filter on a METClean S, from loading to the report on the customer’s phone.

The pre-clean report, from the machine to the customer

METClean S · MET on YouTube · 5 November 2026 · 1 min 48 s

A short film from MET following one filter on a METClean S: loading it, filling in the test ticket, recording the filter’s condition, running the pre-test, and the report arriving in the office inbox and on the customer’s phone.

Nothing loads from YouTube until you press Play; the film then plays in YouTube’s privacy-enhanced mode, and YouTube may store cookies (cookie policy). Watch on YouTube

Load the filter
The filter is connected and clamped in the chamber, ready to test.
Fill in the ticket
Company, operator and the customer’s email go in on the touchscreen.
Record the condition
The technician ticks AdBlue contamination, oil contamination or a blown flexi.
Run the pre-test
The machine measures back pressure through the filter.
Report received
The PDF arrives in the office inbox and on the customer’s phone.

To find the ticket fields and the pre-test on the touchscreen, see the ticket configuration and pre-test chapters of the control-screen video guide.

See the pre-test in the METClean S operating guide and see the pre-test in the XL Multi+ operating guide.

Common questions

What does a DPF pre-clean report show?

The back-pressure reading taken before cleaning, the condition findings the technician ticked (AdBlue contamination, oil contamination, a blown flexi), and the job details: test number, customer, operator, date and time.

How does it help justify a DPF clean?

It puts your evidence in writing. The reading shows the filter is restricted; your inspection and the vehicle’s diagnostics show why. The customer sees all of it before they decide, so the recommendation is easy to trust.

Can I email the report before work starts?

Yes. On the S and XL Multi+ the report goes out as soon as the pre-test finishes, while the filter is still on the machine waiting to be cleaned.

Does the report show the result after cleaning?

No. It records the filter’s condition before cleaning. Straight after the wash the filter is still partly damp, so a reading then would show a higher pressure than its true condition. Once the filter is refitted, reset the DPF values in the ECU with your diagnostic tool and fix whatever caused it to block. A short drive finishes the drying.

Which METClean machines support emailed reports?

The METClean S and the METClean XL Multi+, with MET’s new machine software. Already own one? Ask us and we’ll get it set up.

The technical detail

How the pre-test measures back pressure, why readings are only comparable on the same machine and settings, and what a reading can’t see, such as a cracked filter.

See the report on a real job

Watch a filter go from pre-test to emailed report at MET, or ask us whether your machine supports emailed reports.